DANH MỤC SẢN PHẨM

Tìm kiếm nâng cao

Hỗ trợ trực tuyến

Bình chọn

  • Bạn biết về trang web qua nguồn nào ?
  • Internet
  • Hội chợ,Triển lãm
  • Báo chí
  • Qua tổng đài 1080
  • Người thân,Bạn bè
  • Tờ rơi,Poster
  •  

Tỉ giá ngoại tệ

Đối tác

Thống kê

Số lượt truy cập 3400652   lần

Có 70   khách hàng đang online

Trang chủ » Nồi hấp

Nồi hấp

Nồi hấp tiệt trùng 250 lít HL390-250

10/04/2010 22:59

Nồi hấp tiệt trùng 250 lít HL390-250

D&E-Đài Loan

 

Cabinet type automatic pulse-vacuum
steam sterilizer. Designed for large
capacity and highest flexibility in
processing requirement. Can be used
in a hospital for efficient, high volume
processing of heat and moisture stabile
materials, such as fabrics, wrapped
hard goods, liquid or glassware etc.
Control System: Automatic control system
provides strict control of sterilize
temperature time, pressure, etc.
Sterilizer Cycles: There are 3 pre-programmed
cycle selections that can be process
various load types in this sterilizer.
Unwrapped cycle, Wrapped cycle, and
Liquid cycle.
Automatic Operation: cycle progress
automatic through pulses vacuum,
sterilizing, exhaust, vacuum drying
and venting phases.
Temperature Controller: sterilize
temperature can be set from 121℃
to 134℃ on digital temperature controller.
Setting temperature is achieved the
process of sterilizing cycle will automatic
operating.
Timer: sterilize time and dry time can be set
from 0-99 minutes on digital sterilizing timer
and drying timer. The timer starts only after
the pre-set temperature is reached, ensuring
complete sterilization.
Status Display: illuminated pilot lamps display
status and a buzzer announces the completion
and cuts off the heating power source.

Pressure Gauge: The large diameter of chamber
pressure gauge and jacket pressure gauge
make ideal require reading and indicate high
precision and consistent results.
Heating System: Steam generator: equipped
with a high efficient immersion heater and
automatic feed water device to supply steam
to sterilizer.
Vacuum System: Controlled and monitored
pulses vacuum and drying phase effectively
condition loads of various size and density.
Reducing total sterilization time. System
includes a condenser and water ejector.
Steam Trap: Discharges condensate from
chamber to obtain effective saturated steam.
Air Filter: and effective HEPA filter is used
to prevent contaminated air from entering
into the chamber.
Gasket: Silicone rubber sealing gasket is
applied to an even pressure door seal.
Chamber Shell: Rectangular chamber
provides a large capacity to satisfy
a wide range of sterile processing needs.
Chamber is made of high quality SUS 316L
stainless steel with polished surface. A
double layer construction is thermally
insulated with foil backed fiberglass
insulation.
SAFETY DEVICES
Safety Door Switch: cycle does not start
unless chamber door is locked and also
door-unlocked signal is displayed on
the control panel.
Door Interlock: door safety locking device

keep door from being opened while
chamber is pressurized during cycle.
Safety Valve: releasing steam in case of
excessive chamber pressure.
Overheating Protection Device: high
temperature deviation in chamber actuates
protective device cuts off the heating source
immediately.
Low Water Protection Device: Low water
level in steam generator will actuate audible
alarm and protective device cut off the heating
source immediately.
Circuit Protection Device: Circuit breaker and
fuse protects control units when short circuit
or overload occurs.
Emergency Exhaust: Manual exhaust to vent
the chamber and remove the load in the event
of a power failure or outage
SPECIFICATIONS
Chamber Size (mm): (W)510 x (H)510 x (D)965
Overall Dimensions (mm): (W)860 x (H)1700 x (D)1650
Capacity: 250 Liters.
Door Operation: Manual Hinge Door
Temperature Control: LED Digital
Temperature Controller.
M.A.W.P (Kg/cm2): 2.8
Design Temperature (℃): 141℃
Maximum Working Temperature (℃): 134℃
Sterilizing & Drying Timer: 0 ~ 99 minutes
Electric Power (kw) / Steam Generator: 24kw.
Power: AC: 220v. 50 / 60Hz.
Chamber Material: Stainless Steel SUS316L
Jacket, Chamber Door & Shell Material:
Stainless Steel SUS304

STANDARD ACCESSORIES
Loading Cart: 1pc
Transfer Carriage: 1pc
Users Service / Operation Manual: 1s

Các tin khác

Các tin cùng danh mục: Nồi hấp
Xem tiếp